Shining ToolsBOM:544607 +3.61%19 FCF Margin % is -60.50% as of Mar. 2026. GuruFocus rates BOM:544607 with a GF Score™ of 19/100. The stock has 2 warning signs investors should review. Among 3,030 Industrial Products companies, Shining Tools ranks worse than 94.42% on this metric.
FCF Margin % is calculated as Free Cash Flow divided by its Revenue. Shining Tools's Free Cash Flow for the
six
months ended in Mar. 2026 was ₹-110.7 Mil. Shining Tools's Revenue for the
six
months ended in Mar. 2026 was ₹182.9 Mil. Therefore, Shining Tools's FCF Margin % for the quarter that ended in Mar. 2026 was -60.50%.
The historical rank and industry rank for Shining Tools's FCF Margin % or its related term are showing as below:
BOM:544607'
s FCF Margin % Range Over the Past 10 Years
Min: -60.5 Med: 4.54 Max: 28.07
Current: -60.5
During the past 4 years, the highest FCF Margin % of Shining Tools was 28.07%. The lowest was -60.50%. And the median was 4.54%.
BOM:544607's FCF Margin % is ranked worse than 94.42% of 3030
companies
in the Industrial Products industry
Industry Median: 1.55
vs BOM:544607: -60.50
Shining Tools FCF Margin % Related Terms
Shining Tools FCF Margin % Historical Data
* Premium members only.
The historical data trend for Shining Tools's FCF Margin % can be seen below:
* For Operating Data section: All numbers are indicated by the unit behind each term and all currency related amount are in USD. * For other sections: All numbers are in millions except for per share data, ratio, and percentage. All currency related amount are indicated in the company's associated stock exchange currency.
Shining Tools FCF Margin % Chart
Shining Tools Annual Data
Trend
Mar23
Mar24
Mar25
Mar26
FCF Margin %
21.33
28.07
-12.26
-60.50
Shining Tools Semi-Annual Data
Mar23
Mar24
Mar25
Mar26
FCF Margin %
21.33
28.07
-12.26
-60.50
BOM:544607 vs SNA, RBC, LECO: FCF Margin % Comparison
For the Tools & Accessories subindustry, Shining Tools's FCF Margin %, along with its competitors' market caps and FCF Margin % data, can be viewed below:
* Competitive companies are chosen from companies within the same industry, with headquarter located in same country, with closest market capitalization; x-axis shows the market cap, and y-axis shows the term value; the bigger the dot, the larger the market cap. Note that "N/A" values will not show up in the chart.
Shining Tools FCF Margin % vs Industrial Products Industry
For the Industrial Products industry and Industrials sector, Shining Tools's FCF Margin % distribution charts can be found below:
* The bar in red indicates where Shining Tools's FCF Margin % falls into.
* For Operating Data section: All numbers are indicated by the unit behind each term and all currency related amount are in USD. * For other sections: All numbers are in millions except for per share data, ratio, and percentage. All currency related amount are indicated in the company's associated stock exchange currency.
Shining Tools (BOM:544607) has a FCF Margin % of -60.50% as of Mar. 2026. Free cash flow margin is the ratio of total free cash flow to net sales. View historical data on Shining Tools and its competitors. According to the industry distribution chart, Shining Tools ranks #2861 out of 3030 companies in the Industrial Products industry, placing it in the top 94.4%.
Is Shining Tools' FCF Margin % too high?
Shining Tools' current FCF Margin % is -60.50%. Based on the distribution chart, Shining Tools ranks #2861 out of 3030 companies in the Industrial Products industry, which is in the bottom quartile relative to peers. Overall, Shining Tools has a GF Score™ of 19/100, reflecting its overall financial health beyond just this single metric.
How does Shining Tools' FCF Margin % compare to SNA and RBC?
According to the Industrial Products industry distribution chart, Shining Tools ranks #2861 out of 3030 companies for FCF Margin %. This places Shining Tools in the lower half of its industry. The industry median FCF Margin % is 1.55. See the competitive comparison table and distribution chart on this page for a detailed peer-by-peer breakdown.
What is a good FCF Margin % for an Industrial Products company?
The median FCF Margin % among Industrial Products companies is 1.55, based on 3,030 companies in the industry. Companies in the top quartile (top 25%) have a FCF Margin % significantly above this median, while those in the bottom quartile fall well below. However, FCF Margin % should not be evaluated in isolation — investors should consider it alongside profitability, growth, and financial strength metrics. Use the industry distribution chart on this page to see where any company falls relative to its peers.
What does a high FCF Margin % mean?
A high FCF Margin % can signal that a stock is expensive relative to its fundamentals. Free cash flow margin is the ratio of total free cash flow to net sales. View historical data on Shining Tools and its competitors. For the Industrial Products industry, the median FCF Margin % is 1.55 — values significantly above this may indicate overvaluation, while values below may suggest a bargain or underlying issues. Shining Tools's current FCF Margin % is -60.50%. However, context matters — high-growth companies often justify higher valuations. Always evaluate alongside other metrics like GF Score™ and GF Value™.
Is Shining Tools stock overvalued right now?
Shining Tools (BOM:544607) has a current FCF Margin % of -60.50%. The current FCF Margin % is -60.50%. Shining Tools' overall GF Score™ is 19/100 with 2 warning signs to review. Investors should evaluate multiple metrics — including profitability, growth, and financial strength — before making a decision.
How is FCF Margin % calculated?
FCF Margin % is calculated from a company's financial statements. For Shining Tools (BOM:544607), the current FCF Margin % is -60.50% as of Mar. 2026. GuruFocus calculates this using data sourced from SEC filings and annual reports. See the calculation section and 30-year financial data on this page for the full breakdown.
Shining Tools Ltd is engaged in the designing and manufacturing of high-performance solid carbide cutting tools catering to various industries in India. Additionally, the company provides reconditioning services for used tools, ensuring their extended usability and performance. It is engaged in producing a wide range of high-performance cutting tools, including end mills, thread mills, drills, and reamers, offering tooling solutions for modern manufacturing needs. The company derives the majority of its revenue from the manufacturing of customized tools.
19GF Score
Get the complete analysis for BOM:544607
FCF Margin % is just one metric. See GF Value™, 30-year financials, guru trades, warning signs, and more.
Quick Browse
Personalize
Premium Gurus 
Create New Portfolio
BOM:544607 has been successfully added to your 