Patel Engineering (NSE:PATELENG) Beneish M-Score: -2.50 (As of Jun. 27, 2026)

Patel Engineering Beneish M-Score Related Terms

The historical data trend for Patel Engineering's Beneish M-Score can be seen below:

* For Operating Data section: All numbers are indicated by the unit behind each term and all currency related amount are in USD.
* For other sections: All numbers are in millions except for per share data, ratio, and percentage. All currency related amount are indicated in the company's associated stock exchange currency.

Patel Engineering Beneish M-Score Chart

Patel Engineering Annual Data
	Trend	Mar17	Mar18	Mar19	Mar20	Mar21	Mar22	Mar23	Mar24	Mar25	Mar26
Beneish M-Score		Get a 7-Day Free Trial					-2.25	-2.81	-2.73	-2.52	-2.50

Patel Engineering Quarterly Data
	Jun21	Sep21	Dec21	Mar22	Jun22	Sep22	Dec22	Mar23	Jun23	Sep23	Dec23	Mar24	Jun24	Sep24	Dec24	Mar25	Jun25	Sep25	Dec25	Mar26
Beneish M-Score	Get a 7-Day Free Trial															-2.52	0.00	0.00	0.00	-2.50

NSE:PATELENG vs PWR, FIX, EME: Beneish M-Score Comparison

For the Engineering & Construction subindustry, Patel Engineering's Beneish M-Score, along with its competitors' market caps and Beneish M-Score data, can be viewed below:

* Competitive companies are chosen from companies within the same industry, with headquarter located in same country, with closest market capitalization; x-axis shows the market cap, and y-axis shows the term value; the bigger the dot, the larger the market cap. Note that "N/A" values will not show up in the chart.

Patel Engineering Beneish M-Score vs Construction Industry

For the Construction industry and Industrials sector, Patel Engineering's Beneish M-Score distribution charts can be found below:

* The bar in red indicates where Patel Engineering's Beneish M-Score falls into.

Patel Engineering Beneish M-Score Calculation

The M-score was created by Professor Messod Beneish. Instead of measuring the bankruptcy risk (Altman Z-Score) or business trend (Piotroski F-Score), M-score can be used to detect the risk of earnings manipulation. This is the original research paper on M-score.

The M-Score Variables:

The M-score of Patel Engineering for today is based on a combination of the following eight different indices:

* For Operating Data section: All numbers are indicated by the unit behind each term and all currency related amount are in USD.
* For other sections: All numbers are in millions except for per share data, ratio, and percentage. All currency related amount are indicated in the company's associated stock exchange currency.

1. DSRI = Days Sales in Receivables Index

Measured as the ratio of Revenue in Total Receivables in year t to year t-1.

A large increase in DSR could be indicative of revenue inflation.

2. GMI = Gross Margin Index

Measured as the ratio of gross margin in year t-1 to gross margin in year t.

Gross margin has deteriorated when this index is above 1. A firm with poorer prospects is more likely to manipulate earnings.

3. AQI = Asset Quality Index

AQI is the ratio of asset quality in year t to year t-1.

Asset quality is measured as the ratio of non-current assets other than Property, Plant and Equipment to Total Assets.

4. SGI = Sales Growth Index

Ratio of Revenue in year t to sales in year t-1.

Sales growth is not itself a measure of manipulation. However, growth companies are likely to find themselves under pressure to manipulate in order to keep up appearances.

5. DEPI = Depreciation Index

Measured as the ratio of the rate of Depreciation, Depletion and Amortization in year t-1 to the corresponding rate in year t.

DEPI greater than 1 indicates that assets are being depreciated at a slower rate. This suggests that the firm might be revising useful asset life assumptions upwards, or adopting a new method that is income friendly.

Note: If the Depreciation, Depletion and Amortization data is not available, we assume that the depreciation rate is constant and set the Depreciation Index to 1.

6. SGAI = Sales, General and Administrative expenses Index

The ratio of Selling, General, & Admin. Expense(SGA) to Sales in year t relative to year t-1.

SGA expenses index > 1 means that the company is becoming less efficient in generate sales.

7. LVGI = Leverage Index

The ratio of total debt to Total Assets in year t relative to yeat t-1.

An LVGI > 1 indicates an increase in leverage

8. TATA = Total Accruals to Total Assets

Total accruals calculated as the change in working capital accounts other than cash less depreciation.

An M-Score of equal or less than -1.78 suggests that the company is unlikely to be a manipulator. An M-Score of greater than -1.78 signals that the company is likely to be a manipulator.

Patel Engineering has a M-score of -2.50 suggests that the company is unlikely to be a manipulator.

Patel Engineering Business Description