Macro MetalsASX:M4M Receivables Turnover is 1.31 as of Dec. 2025. The stock has 2 warning signs investors should review. Among 605 Steel companies, Macro Metals ranks worse than 98.51% on this metric.
The Receivables Turnover ratio measures the number of times a company collects its average accounts receivable balance. It is calculated as Revenue divided by average Accounts Receivable. An efficient company has a higher accounts receivable turnover ratio while an inefficient company has a lower ratio. Macro Metals's Revenue for the
six
months ended in Dec. 2025 was A$0.24 Mil. Macro Metals's average Accounts Receivable for the
six
months ended in Dec. 2025 was A$0.18 Mil.
Hence, Macro Metals's Receivables Turnover for the
six
months ended in Dec. 2025 was 1.31.
An efficient company has a higher accounts receivable turnover ratio while an inefficient company has a lower ratio. This metric is commonly used to compare companies within the same industry to check whether they are on par with their competitors.
Macro Metals Receivables Turnover Related Terms
Macro Metals Receivables Turnover Historical Data
* Premium members only.
The historical data trend for Macro Metals's Receivables Turnover can be seen below:
* For Operating Data section: All numbers are indicated by the unit behind each term and all currency related amount are in USD. * For other sections: All numbers are in millions except for per share data, ratio, and percentage. All currency related amount are indicated in the company's associated stock exchange currency.
ASX:M4M vs NUE, STLD, RS: Receivables Turnover Comparison
For the Steel subindustry, Macro Metals's Receivables Turnover, along with its competitors' market caps and Receivables Turnover data, can be viewed below:
* Competitive companies are chosen from companies within the same industry, with headquarter located in same country, with closest market capitalization; x-axis shows the market cap, and y-axis shows the term value; the bigger the dot, the larger the market cap. Note that "N/A" values will not show up in the chart.
Macro Metals Receivables Turnover vs Steel Industry
For the Steel industry and Basic Materials sector, Macro Metals's Receivables Turnover distribution charts can be found below:
* The bar in red indicates where Macro Metals's Receivables Turnover falls into.
* For Operating Data section: All numbers are indicated by the unit behind each term and all currency related amount are in USD. * For other sections: All numbers are in millions except for per share data, ratio, and percentage. All currency related amount are indicated in the company's associated stock exchange currency.
Macro Metals (ASX:M4M) has a Receivables Turnover of 1.31 as of Dec. 2025. The accounts receivables turnover ratio measures the number of times a company collects its average accounts receivable balance. It is calculated as Revenue divided by Average Accounts Receivable. View historical data on Macro Metals and its competitors. According to the industry distribution chart, Macro Metals ranks #596 out of 605 companies in the Steel industry, placing it in the top 98.5%.
Is Macro Metals' Receivables Turnover too high?
Macro Metals' current Receivables Turnover is 1.31. The Steel industry median Receivables Turnover is 7.16. Macro Metals' value of 1.31 is 81.7% below this industry median. Based on the distribution chart, Macro Metals ranks #596 out of 605 companies in the Steel industry, which is in the bottom quartile relative to peers.
How does Macro Metals' Receivables Turnover compare to NUE and STLD?
According to the Steel industry distribution chart, Macro Metals ranks #596 out of 605 companies for Receivables Turnover. This places Macro Metals in the lower half of its industry. The industry median Receivables Turnover is 7.16. Macro Metals' value of 1.31 is 81.7% below this benchmark. See the competitive comparison table and distribution chart on this page for a detailed peer-by-peer breakdown.
What is a good Receivables Turnover for a Steel company?
The median Receivables Turnover among Steel companies is 7.16, based on 605 companies in the industry. Companies in the top quartile (top 25%) have a Receivables Turnover significantly above this median, while those in the bottom quartile fall well below. However, Receivables Turnover should not be evaluated in isolation — investors should consider it alongside profitability, growth, and financial strength metrics. Macro Metals's current Receivables Turnover of 1.31 is 81.7% below the industry median. Use the industry distribution chart on this page to see where any company falls relative to its peers.
What does a high Receivables Turnover mean?
A high Receivables Turnover can signal that a stock is expensive relative to its fundamentals. The accounts receivables turnover ratio measures the number of times a company collects its average accounts receivable balance. It is calculated as Revenue divided by Average Accounts Receivable. View historical data on Macro Metals and its competitors. For the Steel industry, the median Receivables Turnover is 7.16 — values significantly above this may indicate overvaluation, while values below may suggest a bargain or underlying issues. Macro Metals's current Receivables Turnover is 1.31. However, context matters — high-growth companies often justify higher valuations. Always evaluate alongside other metrics like GF Score™ and GF Value™.
Is Macro Metals stock overvalued right now?
Macro Metals (ASX:M4M) has a current Receivables Turnover of 1.31. The current Receivables Turnover is 1.31 and 81.7% below the Steel industry median of 7.16. Investors should evaluate multiple metrics — including profitability, growth, and financial strength — before making a decision.
How is Receivables Turnover calculated?
Receivables Turnover is calculated from a company's financial statements. For Macro Metals (ASX:M4M), the current Receivables Turnover is 1.31 as of Dec. 2025. GuruFocus calculates this using data sourced from SEC filings and annual reports. See the calculation section and 30-year financial data on this page for the full breakdown.
Macro Metals Ltd is a mineral exploration company. The principal activities of the company consist of exploration and evaluation of WA iron ore tenements, acquisition of additional prospective tenements in WA, proposed acquisition of Chilean lithium projects and continued evaluation of Agbaja Cast Steel Project. It operates in one industry segment, which is mineral exploration, evaluation, and development, and operates in two geographic segments: the Federal Republic of Nigeria and Australia.
Quick Browse
Personalize
Premium Gurus 
Create New Portfolio
ASX:M4M has been successfully added to your 